Model Name
FJ Holden
Previous Model and Next Model
48-215(FX), Next model FE Holden
Dates of Production
Introduced:May 1953
Discontinued: July 1956
The FJ Holden was in production for 38 months
Production Figures
169 969
Model Range
Standard Sedan (FJ/215)
Business Sedan (FJ/217)
Special Sedan (FJ/225)
Panel Van (December 1953) (FJ/2104)
Utility (FJ/2106)
Australian Holden Part Finder
- You searched
- plug for Holden Belmont HQ Kingswood HQ
- Part category identified
- Spark plugs → Spark plugs
- Vehicle identified
- HQ Holden Kingswood HQ
We couldn’t find an exact match for plug for HQ Holden Kingswood HQ
That doesn’t mean it isn’t available — it isn’t in our catalogue yet. Try one of these:
Not in our catalogue yet? Search for “Holden Belmont HQ Kingswood HQ plug” at:
These are retailer searches, not confirmed matches — check the part and your vehicle’s fitment on the retailer’s page before buying.
Tell us what you’re after
We add the parts people ask for. Tell us what you were looking for.
Browse by make/series
Prices at Introduction
Standard: £1 023 ($2 046)
Business Sedan: £1 052 ($2 104)
Special Sedan: £1 075 ($2 150)
Panel Van: £985 ($1 970)
Utility: £969 ($1 938)
Exterior Dimensions (Sedan)
Wheelbase: 103 inches (2 620mm)
Total Length: 173.3 inches (4401mm)
Width 66.9 inches (1 699mm)
Kerb Weight 2250lb (1012kg)
Turning circle: 11.3m
Fuel Tank Capacity: 9.5 Gallons (43 litres)
Engines
Grey Engine
Engine Prefix: 121794 to 283372
Capacity: 2160 cc 132.5 cubic inches (2.171 litres)
Type: Conventional, watercooled four stroke, reciprocating piston type
Head Design: Pushrod and rocker actuated ohv with two valves per cylinder
Configuration: Front mounted, longitudinal, inline
Number of Cylinders: 6
Firing Order: 1-5-3-6-2-4
Bore and Stroke: 3 x 3.125 Inches (76.2 x 79.4mm)
Compression Ratio: 6.5:1
Power: 45kW (60bhp) @ 3800 RPM
Torque: 135Nm (100lb-ft) @ 2000 RPM
Fuel System: Stromberg BXOV-1 Carburettor
Transmission
3 Speed Manual
Column Shift
Synchromesh on 2nd and 3rd.
1st: 2.985:1
2nd: 1.591:1
3rd: 1.00:1
Reverse: 2.985:1
Rear Axle
GM-H Banjo
Ratio: 3.98:1
Clutch
Single-plate, dry disc, diaphragm type spring driven plate cushioned to hub by four
high rate coil springs
Body Construction
Monocoque unibody structure
Ignition and Electrical
6 volt battery. Coil and generator
Exhaust
Straight through resonance type muffler to a single tail pipe
Suspension
Front: Short and long arm independent type with coil springs
Rear: Hotchkiss Drive with semi-elliptic springs
Steering
Worm and sector type, ratio 14:1
Brakes
Front: Hydraulic 9 inch (229mm) drums
Rear: Hydraulic 9 inch (229mm) drums
Wheels
Demountable disc wheels with drop centre type rim integral with wheel
Tyres
Low pressure balloon 5.50×15 four-ply (Standard), 5.90×15 four-ply (Special)